Updated October 22, 2026
Kandi cuffs are the wide, beaded bracelets you see traded at festivals and raves — and they look far more complicated than they are. The whole thing is pony beads and elastic, and the technique takes about ten minutes to learn.
Below is the simple single-strand cuff to start with, then the X-base cuff, which is the proper wide one with the criss-cross pattern running through it.
What you’ll need
- Pony beads — the chunky plastic ones with wide holes. A basic cuff takes roughly 30 to 40; a wide X-base cuff needs more like 80 to 100.
- Stretch elastic cord, around 0.8mm. Clear or black both work; black disappears behind darker beads.
- Scissors.
- A big-eye or blunt needle (optional) — worth it for the X-base, where you’ll be passing cord back through beads that are already strung.
The basic kandi cuff
Step 1: Measure the elastic
Wrap the cord around your wrist, then cut it at least three inches longer than that. You need the extra for knotting, and running short with beads already on is thoroughly annoying.
Step 2: String your pattern
Thread the beads on in whatever order you like. Lay the pattern out on the table first if you’re spelling a word or running a colour sequence — it’s much easier than unpicking later.
Leave a couple of inches bare at each end.
Step 3: Knot it
Bring the ends together and tie a surgeon’s knot: a double overhand, pulled tight, then a second double overhand on top. A single knot in elastic will work itself loose, every time.
Trim the tails to about a quarter inch and tuck them back inside the nearest bead so they don’t show.
The X-base cuff
This is the wide version, and the X pattern comes from how the rows connect rather than from the bead colours. It’s built one row at a time on top of a basic cuff.
Step 1: Make the base row
Start with a basic cuff as above, using an even number of beads. This is your foundation, so make it comfortably loose — the finished cuff will be tighter once more rows pull it in.
Step 2: Start the second row
Cut a fresh length of elastic and tie it to the base ring between two beads. Thread on one new bead, skip one bead on the base row, and pass your cord through the next base bead.
Then another new bead, skip one, through the next. Keep going all the way round.
Step 3: Watch the X appear
Because each new bead sits above the gap between two base beads, the cord crosses diagonally between rows — and those crossings are the X shapes running through the cuff.
Keep the tension even. Pulled too tight the cuff cups and won’t sit flat; too loose and the cord shows between beads.
Step 4: Add rows until it’s as wide as you like
Each new row works exactly the same way, threading into the row below rather than the base. Three rows makes a neat narrow cuff; five or six gives you the proper wide festival look.
Knot off each row with a surgeon’s knot and tuck the tails inside a bead.
Design ideas
Spell something. Letter beads are the heart of kandi — names, song lyrics, in-jokes. Count your letters before you start so the word sits centred on the top of your wrist.
Work a colour story. Rainbow order never fails. Two alternating colours shows off the X pattern most clearly, because the crossings stay visible.
Make a pair. Kandi is traditionally made to be traded, so a matching second cuff is never wasted effort.
If beading suits you, our adjustable bracelet guide covers sliding knots for pieces that need to fit anyone, and rubber band bracelets use a similar row-by-row logic with no beads at all.
FAQs
How many beads do I need?
Around 30 to 40 for a single-strand cuff on an average adult wrist. A five-row X-base cuff needs roughly 80 to 100. Always buy more than you think — colour matching a half-finished cuff later is miserable.
What size elastic should I use?
About 0.8mm. Thinner cord slips through pony bead holes too easily and snaps under tension; thicker cord won’t make the double pass the X-base needs.
Why does my cuff curl instead of lying flat?
The tension is too tight on the newer rows. Each row should sit comfortably against the one below without pulling it inwards. Loosen off and let the beads find their own spacing.
How do I stop the knots coming undone?
Use a surgeon’s knot rather than a single or double overhand, and tuck the tails inside a bead. A tiny dab of clear glue on the knot helps if you’re making one to keep.
Can I use a different kind of bead?
Pony beads are standard because the holes are wide enough for several passes of cord. Seed beads are far too small for this technique; use them for strung bracelets instead.

Hi, my name’s Elena Coolidge. I’m a DIY enthusiast who loves building fun woodworking plans. These DIY plans are fun hobby projects for enthusiasts or even more advanced builders that want to build things like bunk beds, end tables or even a duck box!





